OSC BASICS

Woland

2nd Section - MANUAL IP

SELECT "MANUAL", THEN CLICK "ADVANCED"

CLICK THE "TCP/IP" TAB, THEN SELECT "CONFIGURE IPv4", THEN SELECT "Using DHCP with manual address" FROM THE DROPDOWN MENU

SETTING THE MANUAL IP FOR COMPUTER 1

SETTING THE MANUAL IP FOR COMPUTER 2

Woland

Section 3 - ISADORA

>>>Patch pictured in screenshots is attached here<<<

OSC Transmit Isadora Actor

COMPUTER 1 TEST SETUP

COMPUTER 2 TEST SETUP

STREAM SETUP

CHECK "AUTO-DETECT INPUTS"

HOW TO RENUMBER OSC CHANNELS

DIAGRAM OF WHAT'S GOING ON BETWEEN THE COMPUTERS

Hope that helps. Feel free to ask me any questions. I'm fairly certain those are all the steps I took, but my second computer and router are packed away at the moment, so I can't do a test-build as confirmation.

Best wishes,

Woland (Lucas Wilson-Spiro)

Woland

@bonemap said:

@jamie-nesbitt said:
a basic Master/Slave relationship
Have you tried Isadora's 'Net Broadcaster' for your master/slave set up. You only need the computers on the same network and use the combination of Net Broadcaster and Listener actors to assigned channels.

Best Wishes
bonemap

I have also used the Net Broadcaster in the past, but once had an issue with it right before a tech, then taught myself how to do OSC and reprogrammed both computers' Patches to replace the Net Broadcasters with OSC Transmit actors, fell in love with the custom labels (which help in telling what a particular channel is for), and never looked back.

Both are viable options, I just enjoy the customization that OSC allows.

If you're going the Net Broadcaster route, all of the networking steps in Sections 1 and 2 still hold true, it's just section 3 that you'd ignore.

Best wishes,

Woland

Jamie Nesbitt

WOW! Thanks so much for this. Very thorough indeed. I will fill you in on my results.

Woland

@jamie-nesbitt

No problem. Also, I can't seem to leave anything unfinished, so...

>>>Updated Patch (OSC + Net Broadcaster)<<<

SECTION 4 - NET BROADCASTER ACTORS AND LISTENER ACTORS

CLICK "Isadora/Isadora USB)" ON THE TOP LEFT, THEN SELECT "Preferences" FROM THE DROPDOWN MENU

SETTING THE COMPUTER ID FOR COMPUTER 1

SETTING THE COMPUTER ID FOR COMPUTER 2

COMPUTER 1 TEST SETUP

COMPUTER 2 TEST SETUP

DIAGRAM

Best wishes,

Woland

Woland

Also, for those who like to read rather than see pictures:

How to Set a Static IP Address in Mac OS X

Best wishes,

Woland

bonemap

@woland said:

once had an issue with it

Oh that is interesting, what was the issue do you recall?

Best wishes

Bonemap

bonemap

@woland said:

1st Section - NETWORK SETUP

Setting up static ip addresses is a good idea. Sometimes, when working with lots of network devices that include auto IP addresses, you just have to make sure you start-up your devices in the right sequence otherwise you risk ip address conflicts. Thanks for articulating the walk through steps very handy.

Best wishes

Bonemap

Woland

@bonemap

I never figured out what the issue was. We'd gone a few months between tour stops, and when we sat down, the Net Broadcaster setup just wasn't working anymore, so I tried OSC for the first time. I was pressed for time, so I didn't explore it thoroughly. Thinking back on it, after converting everything to OSC, I seem to remember positing that it might have had something to do with me having a newer version on my personal Mac Pro (trash can) than the second Mac Pro had.

Never did figure it out, but I found a solution, so that's all that mattered to me.

Best wishes,

Woland

Woland

Now to begin the arduous process of putting all these photos into a post on my website and writing out actual steps. *sigh*

Woland

It's not done, but this'll be the link for the post on my site pertaining to Lan, OSC, and Net Broadcasters:
https://lucaswilsonspiro.wordp...

It's. So. Detailed.

(Why do I do this to myself?)

Best wishes,

Woland

Edit: I'll probably break this into three or four separate posts, but keep the master post with all of the information as well.

Jamie Nesbitt

@woland Okay good and bad. I was able to get the Net Broadcaster to work but not the Osc. I've attached my screen shots to show you my set up.

Computer 1

Computer 2

Woland

@jamie-nesbitt

Try checking the “Auto-Detect Input” box in the Stream Setup Window.

Best wishes,

Woland

Jamie Nesbitt

@woland I did and nothing.

Woland

@jamie-nesbitt

1. Can you post screenshots of your Network Windows on both computers, and the advanced options where you set the manual IP? You’ll need to make sure they’re both using the same subnet mask (255.255.255.0) and the same router address (below the subnet mask).

2. Do you have an ethernet switch or a wireless router than you can connect them both to via Cat5/Cat5e/Cat6. That’s what I’ve done in the past, as opposed to just running an Ethernet cable between the two computers.

Jamie Nesbitt

@woland Okay I think I got it. Now I'm getting this message

Woland

@jamie-nesbitt

If you haven’t already, delete the space between “Comp” and “2”. Spaces aren’t allowed.

Best wishes,

Woland

Jamie Nesbitt

@woland I realized there was a space betweent Comp2 and the /. So I've got Computer 1 listening to numbers! But I'm still getting the error message on Computer 2

Woland

@jamie-nesbitt

Well if it’s that same error message, try just erasing and retyping the whole line that’s giving you the error.

Best wishes,

Woland